Fluke
1673 FC with FEV300 EV Charging Station Adapter

FLUKE 1673 FC Multifunction Installation Tester with FLUKE FEV300 EV Charging Station Test Adapter Kit

Power up your testing efficiency with the FLUKE 1673 FC EV Kit.

Take full control of electrical installations across domestic, commercial, and industrial environments with this ready-to-use bundle that combines the trusted FLUKE 1673 FC Installation Tester and the FEV300 EV Charging Adapter.

This all-in-one testing solution streamlines both electrical installation verification and EV charge point assessment, helping you save valuable time, stay compliant with standards, and deliver clear, reliable results on every job.

With the FLUKE 1673 EV Kit, you get automated installation test sequences at the touch of a button, user-defined limit alerts for added confidence, and seamless data capture through FLUKE Connect™ for fast, professional reporting.

Also known as the FLUKE 1673 FC EV Kit, FLUKE 1673 EV Kit, or FLUKE 1673 plus FEV300, this complete bundle gives you everything you need to test, verify, and certify with precision and speed.

Why choose this kit?

• One kit, two domains: Validate complete electrical installation safety (BS 7671 workflows) and simulate an EV to activate charging output at Mode 3 stations for both functional and safety checks.
• Finish tests up to 30% faster with automatic installation test sequences and pass/fail validation.
• Document up to 50% faster with FLUKE Connect™ and TruTest™ software — capture, sync and export your measurement data directly to reports.
• Real-world EV checks: Switch CP/PP states, run PE Pre-Test for hazardous touch voltage, and simulate CP “E” and PE “F” (earth fault) error states.
• Built for domestic, commercial and industrial applications: Test RCDs, continuity, insulation and loop impedance across all phases and settings.
• Ergonomic design ensures comfortable handheld use even during extended testing days.

Key capabilities (at a glance):

FLUKE 1673 FC — installation testing simplified

• Auto Test sequence at the touch of a button – speed through full BS 7671 checks.
• FLUKE Connect™ compatibility for wireless syncing of measurement data and streamlined TruTest™ reporting.
• Tests covered: insulation resistance (50–1000 V), continuity test (including the ability to measure motor windings with 10 mA current), loop/line impedance (No-Trip & Hi-Current), PSC/PEFC, RCD trip time & current (types AC, A, F and more), voltage/frequency, phase sequence, voltage drop, Z-Max memory.
• User defined limit warnings alert you when readings exceed set thresholds, ensuring every test result meets your standards.
• Ergonomic design with a balanced handle and intuitive control layout for maximum comfort.
• Safety ratings: CAT III 600 V / CAT IV 300 V; compliant with IEC 61010 and IEC 61557 series.

FLUKE FEV300 — realistic EVSE simulation and safety checks

• Mode 3 AC charging (Type 2 socket or fixed cable; Type 1 option available).
• PE Pre-Test checks for voltage between PE and touch sensor before connecting test gear.
• PP “cable simulation” (open, 13 A, 20 A, 32 A, 63 A) and CP “vehicle simulation” states A–D to open charging and verify communication.
• Fault simulation: CP error “E” and PE error “F” (earth fault).
• Terminals L1, L2, L3, N, PE for installation tester measurements; CP signal output for oscilloscope or multimeter diagnostics.
• Standards and protection: Tests per IEC/EN 61851-1 and IEC/HD 60364-7-722; IP54 housing for use in commercial and industrial applications.

Typical applications

• EV charge point commissioning and periodic inspection (simulate EV, activate output, verify RCD behaviour, earth continuity and Zs).
• Testing and documenting electrical installations in domestic, commercial and industrial environments.
• Fast, automated installation test sequences for periodic inspections and certifications.
• Troubleshooting intermittent EVSE faults using CP waveform access and PP/CP toggling.
• Performing continuity tests and checking measurement data accuracy for long cable runs or motors.

Technical highlights

1673 FC Multifunction Installation Tester

• Insulation test voltages 50, 100, 250, 500 and 1000 V with extensive MΩ ranges.
• Loop/line impedance testing (No-Trip and Hi-Current modes), Z-Max memory, PSC/PEFC calculation up to 50 kA.
• RCD testing for trip time and ramp current across types AC, A and F.
• Phase sequence indicator on 185–600 V.
• Rechargeable Li-ion battery with USB-C charging and BLE wireless connectivity.
• Advanced user defined limit warnings ensure consistent test results across multiple systems.

FEV300 EV Test Adapter

• Input up to 250 V (single phase) / 480 V (three phase), 50/60 Hz, 10 A max.
• States CP A–D, PP open/13/20/32/63 A, CP error E, PE error F.
• Ingress protection IP54 with caps in place.
• Approx. 110 × 45 × 220 mm; ~1 kg including cable.

What comes with the FLUKE 1673 FC?

• FLUKE 1673 FC Multifunction Installation Tester
• Li-ion rechargeable battery
• Heavy-duty mains cord
• Hard carry case
• Zero adapter
• Test leads and probes
• Alligator clips
• USB-C charger
• Hanging strap
• Remote control probe
• FLUKE FEV300 EV Charging Station Test Adapter
• Type 2 connection (with Type 1/Type 2 options depending on kit variant)
• Measurement terminals (L1, L2, L3, N, PE)
• CP output for signal testing

❓ Frequently Asked Questions (FAQ)

Q1: Does the FEV300 let me fully simulate an EV to start the charger output?

A. Yes. It simulates CP states A–D and PP cable ratings, opening the charging cycle so you can take measurements via L1/L2/L3/N/PE. You can also simulate CP error E and PE error F.

Q2: Can I check for dangerous touch voltage on PE before testing?

A. Yes - the PE Pre-Test flags any voltage above 50 V between PE and the touch sensor.

Q3: Which standards does this setup support?

A. The 1670 Series addresses IEC/HD 60364-6 installation tests, and the FEV300 enables EVSE checks per IEC/EN 61851-1 and IEC/HD 60364-7-722.

Q4: What RCD types can the 1673 FC test?

A. It covers Type AC, A and F, with trip time/current and automatic test sequences.

Q5: Is the adapter weather-resistant?

A. Yes - rated IP54 when the protective caps are in place.

Q6: Does the 1673 FC have wireless connectivity?

A. Yes - it supports FLUKE Connect™ for syncing measurement data to TruTest™ reporting and certificate creation.